Comparison table: capability and purchase price
| Machine | Laser source / stated power | Stated working area | Checked purchase price (USD) |
|---|---|---|---|
| xTool F1 Ultra | Fiber + blue diode · 20W fiber; 20W diode (separate sources) | 220 × 220 mm; internal height 145 mm | $2,999.00 · F1 Ultra Standalone |
Price check: 2026-10-08. Prices exclude additional setup, tax and delivery; discounts, availability and bundle contents may change. Recheck the exact configuration before ordering. Specifications retain their individual source-check dates below.
Product cost assumptions
The standalone configuration is the price reference. Quote fixtures, rotary or conveyor only if the intended part requires them. Keep those accessories in machine and accessories, and extraction, installation and training in other startup costs. A checked price is not a delivered quote.
Workflow that changes the economics
For metal tags, measure placement, focus, code verification, unloading and rejects over a complete batch. A short marking pass can coexist with substantial handling time. Enter complete operator minutes per attempt, not an advertised scan speed. The sample must demonstrate contrast, durability and readability on your alloy and finish.
Useable field before utilization
Confirm that the intended part and fixture fit the stated working area. Do not model an accessory-expanded field or unattended production unless the exact configuration and operating procedure have been verified. A sample photograph does not establish throughput or acceptance yield.
Who should buy / who should NOT buy
Consider purchase when paid marking work, accepted samples and a safe installation justify the complete quote. Defer if the plan depends on sheet cutting, untested serial-code readability, or full utilization before any orders exist. Compare outsourcing the exact mark as a fallback.
Sensitivity: the levers worth measuring
Start with half the assumed monthly demand. Then increase rejected attempts or operator minutes using a real sample batch. If contribution becomes non-positive, extra volume cannot repair the unit economics. If sales exceed the time-based capacity, the calculator caps sales rather than crediting impossible output.
Realistic setup-cost categories
- Equipment and accessories: the exact module, bed, fixtures, rotary and any required cooling or air assist.
- Getting operational: delivery access, electrical work, extraction and exhaust routing, installation, training and one-time software.
- Operating costs: blanks, rejects, optics or filters, maintenance reserve, software subscriptions and complete operator time.
- Cash reserve: packaging, selling costs, working capital and lower-sales months; avoid counting a cost twice.
Itemize the installed quote before committing to the machine price.
Throughput, safety and software checks
Ask for a timed complete batch using your material and artwork: setup, loading, supervision, processing, finishing, inspection and cleanup. Advertised motion speed is not sellable units per hour. Confirm material hazards, enclosure and interlocks, exhaust routing, electrical requirements and required supervision against the exact manual and local requirements. Never leave a laser job unattended. Demonstrate your file format, computer and required accessories in the proposed software; confirm license inclusions and ongoing charges in writing.
Use-case matrix: investigate, then validate
| Paid job | Starting branch | Acceptance check |
|---|---|---|
| Clear acrylic signs | CO₂ | Edge, assembly fit and sheet yield |
| Wood personalization | Diode or CO₂ | Contrast, finish and complete handling time |
| Bare-metal marks | Fiber investigation | Alloy, durability, code readability and fixture fit |
This is a starting decision map, not a guarantee that a named machine processes every material or thickness.
Units and months to break even
The equipment starting value is the checked standalone price. All remaining defaults are illustrative assumptions shown in the fields below, not supplier quotes or forecasts. Replace them with your own assumptions. Contribution is selling price minus variable costs, fees and time allowance. Simplified startup recovery units = one-time setup ÷ positive contribution, rounded up, ignoring monthly fixed costs; use target monthly sales below when fixed costs apply. Months = one-time setup ÷ positive monthly surplus. Neither measure guarantees demand or return.
Update the estimate to calculate startup recovery units.
Enter your own economics
Estimate the sales and operator time needed to cover your setup. The starting numbers are an illustrative example, not a machine quote or a forecast.
Your estimate
- Total one-time setup
- —
- Cost per sold item, including time
- —
- Contribution per sold item
- —
- Time-based capacity / month
- —
- Monthly sales for your recovery target
- —
A scenario based on your inputs. It does not establish buyer demand, machine throughput or a guaranteed return. Surplus is after the operator-time allowance, before taxes and financing.
What if sales change?
Each scenario uses the same price, costs and time. Sales are capped by your available production hours. Capacity is an estimate, not a tested machine specification.
| Sales scenario | Demand / month | Sales after time cap | Production hours | Monthly surplus | Recovery (months) |
|---|
Turn the plan into a supplier request.
Copy this draft and add your exact material, artwork and finish. Ask vendors to demonstrate a complete batch before using their cycle time in your estimate.
Check which machine class fits your materialHow the calculation works
- Accepted yield = 1 − rejection rate.
- Cost per sold item = (cost per attempt + operator minutes × hourly time value ÷ 60) ÷ accepted yield + cost per sale + percentage sales fees.
- Contribution = selling price − cost per sold item.
- Monthly operating break-even = fixed monthly costs ÷ positive contribution, rounded up to a whole item.
- Monthly surplus = capped sales × contribution − fixed monthly costs.
- Simple recovery = upfront setup ÷ positive monthly surplus. If surplus is zero or negative, there is no positive recovery period.
- Target sales = (monthly fixed costs + upfront setup ÷ target months) ÷ positive contribution, rounded up.
The basic break-even formula follows the U.S. Small Business Administration’s break-even explanation. The rejection, time allowance, capacity and recovery extensions are MakerSpec Lab’s stated planning assumptions.
What to check outside this model
This is a one-product model with constant price, cost, yield and time. It assumes every produced accepted item is sold within the month. It excludes sales tax, income tax, financing, depreciation, working capital, inventory timing, ramp-up and equipment resale value. Add every applicable operating expense to the relevant field; use a separate cash-flow model for financing. It does not prove that the sales or sample result can be achieved.
Rejected attempts consume a full share of material and operator time; per-sale costs and sales fees apply only to sold items. Production hours include the time you allocate here. Measure machine availability and other bottlenecks separately. A zero time value means your labor is unpriced in the estimate.
Next: review the material buying guides or the acrylic machine specification comparison.
Review the manufacturer option and affiliate disclosure after checking the assumptions and limits above.
Estimate text
Select and copy this text if a file download is unavailable. Inputs stay in this tab.
Sources and limits
- xTool F1 Ultra specifications — 2026-09-30; selected configuration price data — 2026-10-08.
No machine has been tested by MakerSpec Lab. Specifications are manufacturer statements; business-fit judgments are editorial reasoning, not measured comparative performance. No production rate, warranty advantage, customer demand or profit forecast is asserted.
Check your shortlist with the manufacturer
Affiliate link disclosure: The xTool F1 Ultra link below is an affiliate link. If you buy through it, MakerSpec Lab may receive a commission. This is not a hands-on test or a guaranteed purchase recommendation. Verify the configuration, samples, current price and full quote before buying. Full affiliate disclosure.
Continue the purchase decision
Fit Finder: prepare your sample brief · Break-even calculator
P2S versus MF1624 for acrylic · S1 versus MF1624 for wood · F1 Ultra versus B6 for metal